WAKOL MS230 - Elastic Parquet Adhesive

Elastic 1-component parquet adhesive for the elastic installation of mosaic parquet, industrial parquet (min. 16 mm thick, max. 200 mm long), strip parquet (up to a maximum width of 80 mm, max. 600 mm long), and multi-layer parquet on absorbent and non-absorbent substrates indoors. WAKOL MS 230 complies with DIN EN ISO 17178.

Application

Elastic 1-component parquet adhesive for the installation of

• mosaic parquet, according to DIN EN 13488
• industrial parquet, according to DIN EN 14761, min. 16 mm thick, max. 200 mm long
• strip parquet, according to DIN EN 13226, up to a maximum width of 80 mm, max. 600 mm long
• Multi-layer parquet flooring, according to DIN EN 13489, on properly prepared absorbent and non-absorbent screeds indoors.

Combined with WAKOL Dentate Special 5, also suitable as an adhesive with an integrated moisture barrier exclusively for tongue-and-groove parquet flooring on unheated cement screeds up to a maximum of 4 CM% / 90% KRL and unheated concrete floors up to a maximum of 6% by weight / 90% KRL.

Special Features

1. Solvent-free according to TRGS 610
2. Compliant with DIN EN ISO 17178
3. Water-free
4. No wood expansion
5. EMICODE EC1 PLUS: Very low emissions
6. M1 classification for building products according to the standards of the Building Information Foundation RTS sr
7. A+ according to emission category under French law
8. GISCODE RS10, Installation materials, contains methoxysilane
9. Building product tested for emissions according to DIBt principles: Wakol GmbH, 66954 Pirmasens
10. Polish B mark for building products in accordance with EN ISO 17178
11. Connected Systems warranty on the system with approved LOBADUR varnishes and LOBASOL oils from Loba.
12. Suitable for installation over underfloor heating
13. Meets European Community specifications

Technical data

Base raw material: Modified silane polymer

Evaporation time: None

Open time: approx. 40 min.

Setting time: approx. 24 minutes

Cleaning product: WAKOL RT 5960 cleaning wipes, before the adhesive sets

Storage time: 18 months at room temperature

Storage temperature: Not sensitive to freezing

Application and consumption *

TKB B3 800-1000 g/m² mosaic parquet, industrial parquet, small-format prefabricated parquet

TKB B5 700-900 g/m² large-format multi-layer parquet

TKB B11 1000-1200 g/m² strip parquet, industrial parquet, small-format multi-layer parquet

TKB B13 1100-1300 g/m² large-format multi-layer parquet

WAKOL Special Tooth 5 1700-1800 g/m² tongue-and-groove parquet types with a corresponding relative humidity of max. Up to 4 CM% or 90%

* Consumption depends on the surface structure and the absorption capacity of the screed.

Screeds

Both the subfloor and the interior climatic conditions must meet the requirements of current standards and technical data sheets. Screeds must be permanently dry, firm, smooth, and free of cracks, dirt, and substances that impede adhesion.

Perform mechanical pretreatment and thorough vacuuming of calcium sulfate screeds according to the manufacturer's instructions or in accordance with current standards and data sheets. As long as the screed is dust-free, parquet can be glued directly onto the screed. If a primer is necessary, WAKOL Universal Parquet Primer D 3055 can be used on cement-based or calcium sulfate-bonded screeds. On cast asphalt screeds, use only Wakol reactive resin primers such as WAKOL PU 280 polyurethane primer or WAKOL MS 330 silane primer.

On unheated cement screeds up to 4 cm% or 90% relative humidity, Wakol MS Parquet Adhesive can be used as a moisture barrier. When applying WAKOL Special Tooth 5, only the tongue-and-groove parquet types mentioned above are permitted.

Application

Apply evenly to the screed using a notched trowel, avoiding adhesive buildup. 

Install the parquet immediately and press it down firmly. Make sure to moisten the underside of the wood sufficiently.

Clean tools immediately after use with WAKOL RT 5960 Cleaning Wipes. Once set, the adhesive can only be removed mechanically.