ARDEX SE

ARDEX SE - Sanitary silicone for indoor and outdoor use

Sanitary silicone for exterior and interior use on walls and floors for elastic sealing of expansion joints, corner and joint joints in bathrooms, showers and WC's, ceramics, doors, windows and mounting elements in ceramic coverings on balconies, terraces and on facades.

Various colours

Available in boxes of 12 pieces.

Weiss, Grau, Silbergrau in boxes of 20 pieces.

Packaging format
Pack format
Color DE
  • Jassmin
  • Anthrazit
  • Jurabeige
  • Transparent
142521
€137.28
Tax excluded

Description

Sanitary silicone. Exterior and interior. Various colours.

Field of application:

Indoors and outdoors. Walls and floors.

Elastic sealing of expansion joints, corner and junction joints in bathrooms, showers and WC's in the home with ceramic coverings, on doors, windows and mounting elements in ceramic coverings on balconies, terraces and on facades.

Product description:

ARDEX SE is a one-component, acetic acid curing, easily injectable and smoothable silicone sealant. Due to the high elasticity, stretching and undercutting movements are compensated by up to 25 % of the joint width. After curing, ARDEX SE is resistant to weathering, UV radiation and commercially available cleaning and disinfecting agents. The joint is easy to clean. Thanks to its fungicidal finish, it prevents the formation of fungus and mould.

Substrate preparation:

ARDEX SE adheres well to glazed and unglazed tiles, enamels, glass, sanitary acrylic, polished and anodised aluminium, plastic, wood, coated kitchen worktops, solvent-free acrylic lacquers, alkyd resin lacquer and thick-coat glazed lacquer. With concrete, mineral plaster, ARDEX Primer SP 1 should be used; with chrome, stainless steel and hard PVD, ARDEX Primer SP 2 should be used (see adhesion table),

dry and free of dust, dirt, grease, oil and paint. Residues of old sealant must be completely removed. Greasy joint edges as well as the edges of bathtubs and shower trays must be cleaned with suitable cleaning agents.

Deeper joints should be pre-filled with a polyethylene cord with closed cavities. The bottom filling material must not be damaged during insertion. For shallower joints where no round profile fits, the bottom of the joint is covered with polyethylene tape to prevent adhesion on all three sides. Indoors, the joint width must be at least 5 mm, outdoors, at least 10 mm. Under no circumstances should bitumen, tar, oil or acrylic waterproofing materials or acrylic waterproofing materials be used.

Instructions for use:

Cut the tip of the cartridge above the thread, unscrew the nipple and cut crosswise according to the joint width. Insert the cartridge into the gun. Inject ARDEX SE into the joints in such a way that a bond is made between the joint flanks over the entire surface to achieve good adhesion. In case of angled joints, inject in a triangle.

Before film formation (approx. 10 - 12 minutes), smooth the seal with a suitable tool moistened with ARDEX SG smoothing agent and remove the adhesive tape. It is possible to work in sections, as fresh ARDEX SE adheres perfectly to the hardened material, provided that the surface is free of dirt and dust.

The width of the joint must be measured in such a way that the practical expansion capacity of 25% is not exceeded by the movements of the adjoining construction elements (expansion, underlayment). The joints - in relation to the joint width - must comply with the following depths:

In the case of joint fillings on exteriors, the joint width and depth must be at least 10 mm. 

ARDEX SE is to be used at temperatures above + 5°C and below + 40°C.

Recommendations:

ARDEX SE is waterproof and prevents water from entering the joint. However, despite this, necessary waterproofing work should not be avoided.

ARDEX SE must not be painted or used for building joints. It is suitable for edge joints in floor areas, but is not suitable for joints in floors with heavy mechanical loads.

Despite the fungicide finish, care must be taken in sanitary areas to ensure that the joints are kept clean with standard detergents, as dirt and soap residues can serve as a breeding ground for fungi and algae. In addition, from time to time, it is advantageous that the seals are dried and, depending on the load, cleaned with a suitable disinfectant.

Started cartridges can be stored for several days, if the opening of the nozzle is closed with a sealant plug. Before continuing, this plug can be easily removed.

If necessary, any contamination from fresh residues can be removed immediately with thinner. After hardening, this is only possible by mechanical scraping, if the substrate is suitable for this.

In the case of varnished and plastic substrates, a prior adhesion and compatibility check is recommended. If ARDEX SE comes into contact with bituminous substrates, discolouration or loss of adhesion may occur. If iodine disintegrating detergents or disinfectants are used, discolouration may occur.

The following substrates are not suitable: bitumen, butyl, EPDM, rubber, polyethylene, marble and natural stone, neoprene, tar and Teflon. ARDEX SE does not adhere to polyethylene and Teflon. Other substrates may cause discolouration of the sealant.

ARDEX ST natural stone silicone is recommended for coatings of this type.

Natural stone and tiles with open pores should be protected with a suitable smooth adhesive tape. The smoothing agent must not reach the surface of these tiles and dry on top of it, as this could lead to staining.

Caution:

Contains acetic acid. Keep out of reach of children. Avoid contact with eyes and skin.

Avoid contact with eyes and skin. If contact occurs, rinse thoroughly with water.

water, if necessary consult a doctor.

Technical data

(based on tests carried out in our laboratory according to current regulations)

Composition: Silicone, acetic acid hardener

Ingredients: Monocomponent

Consistency: Pasty

Density DIN 52451: Approx. 1,0 g/cm.3

Joint width: Up to 30 mm

Application temperature: +5º C to + 40º C (substrate temperature)

Film formation time*: Approx. 10 - 12 minutes, after a few hours the skin is severely vulnerable. 

Speed of complete drying*: Approx. 2 mm / day

Approx. 7 mm / week

Temperature resistance: - 40° C to + 180° C

Practical expansion capacity: Approx. 25% of the joint width

Modulus E 100%: Approx. 0.40 N/mm2 (DIN EN 28339 Procedure A)

Shore hardness A: Approx. 25

Consumption:

10 mm x 10 mm approx. 3.0 ml/cartridge.

5 mm x 5 mm approx. 12.0 ml/cartridge

In case of triangular seals, the consumption is halved.

Packaging: 310 ml cartridges net, in packs of 12 or 20 units

Storage: Approx. 24 months in cool, dry place in sealed original packaging

Product Details

Family
Silicones and Adhesives
Application
Indoor and outdoor
Components
Single component
Composition
Silicone
Support
Floor and wall
Normative UNE
UNE-EN 15651
Drying time
Normal
GEV-EMICECODE
Not

Attachments

Reviews (0)

No reviews

Related products

Product added to wishlist
Product added to compare.

SPECIAL OFFER

EASTER WEEK 2024

from March 27 to April 1, 2024

10% discount on all products

using the coupon: SANTA2024

IMPORTANT ANNOUNCEMENT

Due to the Easter holiday period, orders placed between

03/27/2024 and 04/01/2024 will be processed starting Tuesday, April 2.

Sorry for the inconvenience.