Seirecolor - One-component acrylic paint

Product description:

SEIRECOLOR is a coloured, single-component, medium viscosity paint based on acrylic resins in aqueous dispersion.

SEIRECOLOR makes the coated surfaces impermeable to water and CO2, easy to clean and offers medium-low mechanical and chemical performance as well as easy maintenance.

Satin-matt finish

After hardening, SEIRECOLOR is impermeable to water and CO2, resistant to chemicals, frost and weathering as well as breathable to water vapour. After hardening, SEIRECOLOR can be washed with water or detergent.

Field of application:

• Protection of concrete structures and elements.
• Anti-carbonation paint on concrete.
• Finishing of facades and interior decoration, both in homes and industrial buildings.
• Finishing of sports floors.
• Accesses to houses, pavements, traffic islands, etc.
• Colour coat for asphalt agglomerates.
• Indoor and outdoor use

Substrate preparation:

The substrate must be hard, solid and free of dust or other loose particles such as paint, remains of lime, mortar, plaster, adhesive residues, etc., which may impair adhesion to the substrate. Concrete surfaces may be damp but not wet.

Before mechanical preparation, varnish, wax, grease, oil and similar contaminants must be removed. Contaminated concrete surfaces must be treated mechanically, either by sanding or diamond grinding, followed by vacuuming.

Any joints or cracks in the concrete substrate where differential movement is anticipated (e.g. expansion joints) shall be respected and suitably sealed.

Priming:

Prior to the application of SEIRECOLOR the substrates, depending on their absorption, must be primed with ACRISIL IMPRIMACIÓN or with SEIRECOLOR itself diluted with 5 - 10% water.

During application and curing, especially in confined areas, adequate ventilation must be ensured.

Recommendations:

SEIRECOLOR should be shaken before use.

Limitations:

Always use SEIRECOLOR at room and/or substrate temperatures not lower than 10°C and always at least 3°C above the dew point.

Nor can it be applied at ambient and/or substrate temperatures above 30°C or when the ambient humidity exceeds 85%.

Avoid prolonged standing water as this may cause softening.

All SEIRE products are manufactured under strict quality controls and procedures, however, it is recommended when colour consistency is essential that the products used are from the same batch.

How to apply:

It can be applied by brush, roller or by mechanical spraying.

For optimum durability of the coating two coats should be applied with an interval of 24 hours between coats.

Consumption:

Approximate consumption of SEIRECOLOR is 0.5 kg/m² in two coats and according to support.

Cleaning tools:

SEIRECOLOR can be cleaned from tools and equipment with water immediately after use. In case the product hardens it can only be removed by mechanical means or organic solvents.

Residues/Spillages:

Spillage of any of the products must be collected immediately with sand, vermiculite or any other inert material and deposited in a suitable container for management.

Waste management of these spills and empty containers should be carried out in accordance with local legislation.

For further information refer to the safety data sheet.

Storage:

The shelf life of SEIRECOLOR is 6 months, in the original closed containers. Storage should be in a dry place between +5ºC and +30ºC. Protection from frost and direct sunlight and heat sources is required.

Precautions:

In case of skin contact, rinse with soap and water. If applied indoors, ensure good ventilation of the room. After drying, the product is physiologically and ecologically neutral.

For further information, see safety data sheet.

Technical data

• Density: Approx. 1,4kg/l
• Coverage: 0,5Kg/m2 in two coats and depending on the substrate.
• Solids content: 62% by weight.
• Dry to touch (20ºC, humidity <50%): After 6h approx.
• Initial curing (20ºC, humidity<50%): 24 hours
• Total curing: 7 days
• Packaging: 25Kg net weight cans