ARDEX X77

ARDEX X78 - Flexible cement-based adhesive for low porosity materials

Flexible cementitious adhesive for low porosity flooring materials. Powder based on cements, additives, special additives, MICROTEC fibres and flexible synthetic materials. The application time is approx. 5 hours. The mortar hardens by hydration and drying. Complies with EN 12004 C2 FEE S1.

Color ES
  • Gray
Packaging format
142457
€42.98
Tax excluded

Description

C2FEES1   EC1 Plus   EC1 Plusflexmortel_100x.png   Marcado CE       microtec_250x.png

Flexible cementitious adhesive for low porosity floor materials. Composite powder based on cements, additives, special additives, MICROTEC fibres and flexible synthetic materials. The application time is approx. 5 hours. The mortar hardens by hydration and drying. Complies with EN 12004 C2 FEE S1.

Field of application:

Interiors and exteriors. Floors

Laying of:

  • ceramic tiles, stoneware and porcelain tiles
  • glass and porcelain mosaics
  • concrete cut stone
  • natural stone with low moisture sensitivity

Laying of tiles and slabs:

  • on balconies and terraces
  • in swimming pools
  • on floors with underfloor heating
  • in industrial and commercial areas with high load-bearing capacity
  • Laying and grouting of tiles on concrete and masonry floors still in the shrinkage phase (at least 3 months old).

Product description:

Composite powder based on cements, additives, special additives, MICROTEC fibres and flexible synthetic materials.

When mixed with water, a soft, paste-like adhesive mortar with high stability is obtained. The application time is approximately 5 hours. The mortar hardens by hydration and drying.

Preparation of the substrate:

The substrate, dry or wet, must be firm, able to bear weight, resistant, free of dust, dirt or separating elements.

Gypsum substrates, as well as porous or sanded floors, must be dry and a first coat of ARDEX P51 primer, diluted with water 1:3, must be applied.

Non-porous substrates made of metal, glass, varnish paints, etc. in interiors must be pre-coated with ARDEX P82, synthetic resin.

In interiors, existing ceramic substrates must be pre-treated with either a first coat of ARDEX P82 or a thin coat of ARDEX X78.

In permanently damp areas and outdoors, substrates should be pre-treated with Ardex waterproofing agents.

Directions for use:

Pour clear water into a clean mixing bowl and mix a corresponding quantity of ARDEX X78 powder until a lump-free, elastic and stable mortar is obtained.

The mortar should be stirred again before application on the substrate to improve its elasticity.

Approximately 9 litres of water are required to mix 25 kg of ARDEX X78 powder.

The consistency of the mortar may vary slightly in each case, depending on the type, size and weight of the coatings to be applied.

ARDEX X78 powder is mixed with ARDEX E 90, diluted with water at a mixing ratio of 1:2, to obtain a special adhesive with high deformability and water-repellent properties.

The mixing ratio is approx:

25 kg ARDEX X78 powder

4.5 kg of ARDEX E 90

8.5 litres of water

ARDEX X78 mortar is applied to the floor and combed with a notched trowel in such a way as to ensure adhesion of the tiles over their entire surface. The choice of trowel is determined by the type, size and back of the tiles.

Rough and uneven floors can be levelled with ARDEX X78. Once the levelling layer has dried, tiling can be carried out.

Tile fixing surfaces should not be larger than the established application time allows and should be laid on a damp, pasty bed.

Tiles can be corrected up to 30 minutes after laying.

If paper-coated glass and porcelain mosaic tiles are laid on the front side, ARDEX X78 should be applied liberally so that when the mosaic is pressed down the product protrudes above it. In this case, subsequent grouting should also be carried out with ARDEX X78.

In case of doubt, carry out a preliminary test.

ARDEX X78 should be worked at temperatures between 5°C and 30°C.

Higher temperatures shorten processing and laying times; lower temperatures lengthen them.

Recommendations:

When laying tiles on building slabs, care must be taken when fixing the tiles to the internal substrate to ensure that the tile installation is strong and stable.

We recommend using ARDEX waterproofing products for waterproofing.

Products from the ARDEX natural stone system are suitable for the stain-free installation of marble and other natural stone in interiors.

In spas, saunas and public swimming pools, use ARDEX WA, adhesive and epoxy grout.

When laying tiles on floors in the shrinkage phase, the field dimensions must be limited by the use of expansion joints.

Product Details

Family
Adhesives
Application
Indoor and outdoor
Components
Single component
Composition
Cementitious
Support
Floor
Normative UNE
UNE 12004 C2 FEE S1
UNE 12004 - Type
C - Cementitious adhesive
UNE 12004 - Adherence
C2 - High adhesion
UNE 12004 - Drying time
F - Quick dry
UNE 12004 - Slipping
Normal slip
UNE 12004 - Open time
EE - Double Extended Open Time
UNE 12004 - Deformability
S1 - Deformable
Flexmortel
Si
Microtec
Yes
Ardurapid effect
No
GEV-EMICECODE
EC1 Plus
Marked CE
Yes
Quality certificate
ISO 9001 - LLoyds Register Quality Assurance Limited

Attachments

Reviews (0)

No reviews

You might also like

Customers who bought this product also bought:

Customers who bought this product also bought:

Product added to wishlist
Product added to compare.